manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 162

REMARK

• To cancel the kickdown, operate the directional lever. In the manual shift mode, the kickdown can also be

canceled by setting the gear speed switch to a position other than the 2nd.

• When the starting switch is turned to OFF position and then to ON position again while the gear speed is

kicked down, the kickdown is canceled.

• Even if the auto-kickdown is enabled, the downshift or the change to P mode with this kickdown switch is

enabled.

• In the auto-shift mode, if the travel speed increases after a kickdown, the gear speed is shifted up automati-

cally.

• In the auto-shift mode, when the travel speed is above 14 km/h in 3rd gear speed or above 26 km/h in 4th

gear speed, the gear speed is not shifted down to prevent the engine from overrunning even if the kickdown
switch is pressed.

MONITOR BRIGHTNESS SELECTOR SWITCH

The  monitor  brightness  selector  switch  is  used  to  select  the
brightness  (luminosity)  of  the  machine  monitor  and  rear  view
monitor while lamp switch is turned ON.
When operating the machine with the headlamp lighting up dur-
ing  the  day,  if  this  switch  is  set  to  Day  mode,  monitor  screen
does not loose the brightness.

(A) Day position

The monitor screen is set to the day mode.

(B) Night position

The monitor screen is set to the night mode.

REMARK

When the lamp switch is turned to OFF position, operating this switch does not change the brightness.
For the fine adjustment method of brightness of the machine monitor, see “SCREEN ADJUSTMENT (3-81)”.
For  the  fine  adjustment  method  of  brightness  of  the  rear  view  monitor,  see  “BRIGHTNESS  ADJUSTMENT
SWITCH OF REAR VIEW MONITOR (3-98)”.

BRIGHTNESS ADJUSTMENT SWITCH OF REAR VIEW MONITOR

The brightness adjustment switch of rear view monitor is used
to adjust the brightness of the rearview monitor.
If  you  release  your  hand  from  the  switch,  it  automatically  re-
turns to its original position.
The brightness in the day and night modes can be adjusted in-
dividually.

Position (A)

The rearview monitor becomes brighter.

Position (B)

The rearview monitor becomes darker.

EXPLANATION OF COMPONENTS

OPERATION

3-98

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды