Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 304 / 432

background image

COLD WEATHER OPERATION

COLD WEATHER OPERATION INFORMATION

If the ambient temperature becomes low, it becomes difficult to start the engine, and the coolant may freeze.
Follow the instructions described as follows.

FUEL AND LUBRICANTS

Change fuel and oil with ones of low viscosity for all components.
For the details of specified viscosity, see “RECOMMENDED FUEL, COOLANT, AND LUBRICANT (7-4)”.

COOLANT

k

k

WARNING

• Coolant is toxic. Be careful not to get it into your eyes or on your skin. If it should get into your eyes

or on your skin, wash it off with large amount of fresh water and see a doctor immediately.

• When handling the cooling water containing coolant that has been drained during changing the

coolant or repair of radiator, contact your Komatsu distributor or request a qualified company to
perform the operation. Coolant is toxic, so never pour it into drainage ditches or drain it onto the
ground surface.

NOTICE
Komatsu recommends the use of Non-Amine Engine Coolant (AF-NAC) for the coolant.

Non-Amine Engine Coolant (AF-NAC) is already diluted with distilled water, so it is not flammable.
For details on the coolant change interval and the density of Non-Amine Engine Coolant (AF-NAC), see “METH-
OD FOR CLEANING INSIDE OF COOLING SYSTEM (4-20)”.

DEF

NOTICE

• DEF freezes at –11 °C.

If DEF in DEF tank freezes, it may expand to break the devices in the tank. The parts inside the tank
may be affected. Add DEF to the specified amount for cold weather (below the level of when DEF
may freeze).
For the specified amount of DEF, see “METHOD FOR CHECKING DEF LEVEL AND ADDING DEF
(3-167)”.

• If DEF or the machine equipped with DEF system cannot be stored when the outside temperature is

lower than –11 °C, DEF in the tank may freeze. Ask your Komatsu distributor for discharging of DEF,
and keep it in the condition free from freezing.

BATTERY

k

k

WARNING

• Battery generates flammable gas. Never bring any open flame near fuel.
• Battery electrolyte is dangerous object. If it gets in your eyes or on your skin, wash it off with a

large amount of water and consult a doctor.

• Battery electrolyte dissolves paint. If it gets on the bodywork, wash it off immediately with water.
• If the battery electrolyte is frozen, do not charge the battery or start the engine with a different pow-

er source. There is danger that the battery may explode.

• Battery electrolyte is toxic. Do not let it flow into drainage ditches or spray it on to the ground sur-

face.

COLD WEATHER OPERATION

OPERATION

3-240

«
...
302
303
304
305
306
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Kato Imer Страницы: 120

Бренд: Case Страницы: 366

Бренд: Takeuchi Страницы: 214

Бренд: Parkside Страницы: 35

Бренд: Vectra Fitness Страницы: 96

Бренд: Woody Страницы: 28

Бренд: Toro Страницы: 60

Бренд: Buhler Страницы: 8

Бренд: SDLG Страницы: 782

Бренд: OverBilt Страницы: 11

Бренд: Noblelift Страницы: 105

Бренд: Gehl Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды