Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 298 / 432

background image

TRANSPORTATION

TRANSPORTATION PROCEDURE

When transporting the machine, choose the transportation method in reference to the weight and dimensions
shown in “SPECIFICATIONS (5-2)”.
Note that the “SPECIFICATIONS” (weight and dimensions) vary depending on the type of tire and bucket.

LOADING AND UNLOADING WITH TRAILER

k

k

WARNING

• When loading or unloading the machine, run the engine at a low speed and operate the machine

slowly in low travel speed.

• Select a flat and firm ground when loading or unloading the machine.

Maintain a safe distance from the road shoulder

• Use ramps with ample width, length, thickness, and strength and install them with a maximum slope

of 15 °.
When using piled soil, compact the piled soil fully to prevent the slope face from collapsing.

• Remove mud from the undercarriage of the machine so that the machine will not slip sideways on

the ramps.
In addition, remove water, snow, ice, grease, oil, etc. from the ramps.

• Never correct your steering on the ramps. There is danger that the machine may tip over.

If it is necessary to change the travel direction, return to the ground or to the bed of the trailer, then
change the travel direction.

• The center of gravity of the machine shifts suddenly at the joint of the ramps and the trailer, so

there is a danger of the machine losing its balance. Accordingly, pass this point slowly.

When loading or unloading, always use ramps or a platform. Proceed as follows.

PROCEDURES FOR LOADING MACHINE

Load on a firm and level ground.
Maintain a safe distance from the road shoulder
1.

Apply the brake of the trailer securely.

2.

Set chocks (1) to the front and rear of the tires to secure
the trailer.

3.

Set right and left ramps (2) parallel to each other and
equally spaced to the right and left of center (3) of the trail-
er. Make angle of installation (4) a maximum of 15 °.
If the ramps bend a large amount under the weight of the
machine, put blocks (5) under the ramps to prevent them
from bending.

4.

Set the travel direction toward the ramps and drive slowly
for loading.

5.

Load the machine correctly in the specified position on the trailer.

METHOD FOR SECURING MACHINE

After loading the machine onto a trailer, secure the machine as follows.
1.

Lower the work equipment gently.

TRANSPORTATION

OPERATION

3-234

«
...
296
297
298
299
300
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: ahlmann Страницы: 103

Бренд: ahlmann Страницы: 113

Бренд: Takeuchi Страницы: 194

Бренд: BARKO LOADERS Страницы: 112

Бренд: Worldwide Construction And Forestry Division Страницы: 20

Бренд: Shini Страницы: 29

SAL-700G Series

Бренд: Shini Страницы: 34

Бренд: Bush Hog Страницы: 42

Бренд: Bush Hog Страницы: 102

Бренд: Bush Hog Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды