Komatsu WA380-8 страница 149 Скачать руководство пользователя | Manualshive

Страница: 149 / 432

background image

4.

When day display (C) is highlighted in yellow, operate the
switches as follows to change day display.
When it is not necessary to change the day setting, press
ENTER switch (4).

(1) UP switch

Advances calendar one day.

(2) DOWN switch

Puts calendar back one day.

(3) RETURN switch

Cancels change and returns to setting for month.

(4) ENTER switch

Accepts change and returns the screen to the “Clock Adjustment” screen.

TIME SETTING

Adjust the time of the machine monitor clock.
1.

Select “Time” from the “Clock Adjustment” menu, and
press ENTER switch (4).

REMARK

If “ON” is selected for the setting of “GPS Synchroniza-
tion”, you cannot select the “Time”.

2.

The “Time” screen is displayed.
When time display (D) is highlighted in yellow, operate the
switches as follows to change time display.
When it is not necessary to change the time setting, press
ENTER switch (4).

(1) UP switch

Advances time one hour.

(2) DOWN switch

Puts time back one hour.

(3) RETURN switch

Cancels the change and returns the screen to “Clock Adjustment” menu.

(4) ENTER switch

Proceeds to setting for minute.

OPERATION

EXPLANATION OF COMPONENTS

3-85

«
...
147
148
149
150
151
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: jcb Страницы: 16

Бренд: Norfield Страницы: 67

Бренд: Terex Страницы: 83

PT100G Forestry

Бренд: Terex Страницы: 142

BOXER 427 Operators

Бренд: Compact Power Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды