Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 57 / 432

background image

• Never use concrete blocks for supports. Concrete blocks

may break under even light loads.

USE PROPER TOOLS

Use the tools suited to the task and use them correctly. Using
damaged, deformed, or low quality tools, or making improper
use of the tools may cause serious personal injury or death.

PRECAUTIONS FOR CHECK AND MAINTENANCE

TURN BATTERY DISCONNECT SWITCH TO OFF POSITION

In the following cases, turn the starting switch to OFF position and check that the system operating lamp is off.
Then set the battery disconnect switch to OFF position and remove the switch key.
If you check and handle battery without turning battery disconnect switch to OFF position, serious personal in-
jury or death by such as an electric shock may occur.

• When storing the machine for a long time (more than 1 month)
• When repairing the electrical system
• When performing electric welding
• When handling the battery
• When replacing the fuse, etc.

PRECAUTIONS FOR WELDING

Welding operations must always be performed by a qualified welder and in a place equipped with proper equip-
ment. There is a hazard of gas, fire, or electric shock when performing welding, so never allow any unqualified
person to perform welding.

HANDLE BATTERY

Before inspecting or handling the battery, turn the key in the starting switch to OFF position and check that the
system operating lamp is off. Then set the battery disconnect switch to OFF position and remove the switch key.

Danger of battery exploding

When the battery is being charged, flammable hydrogen gas is generated and may explode. In addition, the bat-
tery electrolyte includes dilute sulphuric acid. Any mistake in handling may cause serious personal injury, explo-
sion, or fire, so always observe the following.

• Do not use or charge the battery if the battery electrolyte is below LOWER LEVEL mark. This may cause

an explosion. Always perform periodic inspection of the battery electrolyte level, and add purified water
(such as a commercial battery fluid) to UPPER LEVEL mark.

,&

SAFETY

PRECAUTIONS FOR MAINTENANCE

2-37

«
...
55
56
57
58
59
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Kanga Страницы: 100

Бренд: Case Страницы: 41

Бренд: Barreto Страницы: 28

Бренд: Woody Страницы: 28

Бренд: Kubota Страницы: 134

Бренд: Kubota Страницы: 134

Бренд: Kubota Страницы: 138

Бренд: Kubota Страницы: 144

Бренд: Kubota Страницы: 168

Бренд: Kubota Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды