Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 264 / 432

background image

The transmission cut-off pilot lamp flashes for 2 seconds after the buzzer sounds in step 4.
Beep of the buzzer sounds, and the adjusted cut-off position is canceled.

METHOD FOR BRAKING WHILE ACTIVATING TRANSMISSION CUT-OFF FUNC-
TION

If you depress the brake pedal when the transmission cut-off switch is ON, the transmission is set to NEUTRAL
position at the adjusted brake pedal depressing position.

REMARK

When the transmission cut-off switch is OFF, the transmission is not set to NEUTRAL unless the directional lev-
er is shifted to (N).

METHOD FOR STEERING MACHINE

k

k

WARNING

• Avoid steering during high-speed travel or steering on a steep slope, since it is dangerous.
• If the engine is stopped during travel, the secondary steering is actuated. Note that this is only a

secondary steering system, so do not stop the engine during travel.
It is particularly dangerous if the engine is stopped while the machine is traveling on slopes, so
never try such practice.
If the engine stops, place the machine immediately in a safe place.

• When the machine is traveling, turn steering wheel (1) to

the desired direction, then the machine turns to the direc-
tion.
Front and rear frames of this machine articulates around
the connection pin (center pin) at which the 2 frames are
connected with each other and the rear wheels follow the
trace of the front wheels.

• Turn the steering wheel lightly as it follows the turning of machine.

NOTICE
When steering the machine fully, if the steering wheel
is turned to its stroke end, do not try to turn it further.
Check that play (a) of steering wheel is 50 to 100 mm,
and that operation of steering wheel is normal. If any
problem is found, ask your Komatsu distributor for in-
spection.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-200

«
...
262
263
264
265
266
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

IMPULSE IR LOADER

Бренд: TC Electronic Страницы: 8

Бренд: Bush Hog Страницы: 1

Бренд: Bush Hog Страницы: 1

Бренд: AEM Страницы: 528

Бренд: Vermeer Страницы: 104

Бренд: Gehl Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды