Komatsu WA380-8 Скачать руководство пользователя

Страница: 156 / 432

REMARK

• While message display (1) is lit on the standard screen,

when menu switch (2) is pressed, User Message menu
screen (G) is displayed automatically.

• When the starting switch is turned OFF while there is any

unread message, the message is displayed on the end
screen, and when the monitor is started next time, the
message changes to a read message.

• The message is deleted when it becomes out of date or

when a new message reaches.

CHECK MESSAGE

Select message display menu screen (G), and you can read
the arrived message.

(A) Subject of message

When no message has been received, “No message.” is dis-
played.

(B) Serial No. of message

(C) Validity

(D) Text

(E) Reply field

In case of a message requesting for reply, the “Numeric Input: [ ]” is displayed. Make any reply to the message.

REPLY TO MESSAGE

When replying to a message, input the selected item num-
ber shown in the text of the message by using the switch
panel.

• Each switch of the switch panel corresponds to the

number shown on the lower right of the switch.

• The input number is displayed in “Numeric Input: [ ]”of

the reply field.

• If you input an incorrect number, press RETURN

switch (1), and you can clear an input character at a
time.

• If RETURN switch (1) is pressed while no number is entered, the display returns to the standard

screen.

After inputting a selected item number, press ENTER
switch (2).

EXPLANATION OF COMPONENTS

OPERATION

3-92

Содержание WA380-8

















































































































































































































































































































































































































































Результаты поиска

Содержание WA380-8

Отзывы:

Похожие инструкции для WA380-8

Бренды по названию

Популярные бренды

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание WA380-8

Отзывы:

Похожие инструкции для WA380-8

Бренды по названию

Популярные бренды