Komatsu WA380-8 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 432

Komatsu WA380-8 Скачать руководство пользователя страница 94

MAINTENANCE TIME CAUTION LAMP

Maintenance time caution lamp displays notices and alarms
concerning maintenance time.
This lamp lights up when the starting switch is turned to ON po-
sition. It goes out after 30 seconds and the display changes to
the standard screen.

• When lamp lights up in red

The maintenance due time is over.
If no action is taken, the machine performance will become
worse and the machine life will be shortened. Perform nec-
essary maintenance as soon as possible.

• When lamp lights up in yellow

The maintenance due time is approaching.
Prepare necessary parts for the maintenance.

REMARK

• To check the items that need maintenance, see the “Maintenance” menu screen.
• On the standard screen, when the menu switch is pressed while the lamp is lit, the screen changes directly

to the “Maintenance” menu screen.

• For operations on the “Maintenance” menu screen, see “MAINTENANCE SCREEN SETTING (3-75)”.
• By default, the maintenance time caution lamp (yellow) is set to light up when the remaining time reaches

30 hours. However, you can change this setting. To change the setting, ask your Komatsu distributor.

CENTRALIZED WARNING LAMP

The centralized warning lamp lights up in red and at the same
time the alarm buzzer sounds intermittently when the machine
is in any of the following conditions.

Machine conditions under which centralized warn-

ing lamp lights up

Other monitor displays

When action level L02, L03, or L04 is displayed on
the machine monitor.

When the engine overrun caution lamp is lit.

When the brake oil pressure is below the specified
value while the engine is running.

The brake oil pressure caution lamp lights
up.

EXPLANATION OF COMPONENTS

OPERATION

3-30

«
...
92
93
94
95
96
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды