Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 404 / 432

background image

Position (a): RAISE
When  the  multi-function  mono-lever  is  pulled  further  from  the
“RAISE” position, the lever stops in that position.
When the remote boom positioner is enabled, the boom stops
at the preset position and the lever returns to “HOLD” position
at the same time.
When the remote boom positioner is disabled, the boom stops
at the highest position and the lever returns to “HOLD” position
at the same time.
Position (b): HOLD
The boom and bucket remain in the positions where they are stopped.
Position (c): LOWER
Position (d): FLOAT
The boom moves freely under external force. When the lever is set to “FLOAT” position, the lever stops in that
position.
When  the  remote  boom  positioner  is  enabled,  the  boom  stops  at  the  preset  position  and  the  lever  returns  to
“HOLD” position at the same time.
When it is disabled, the lever remains in “FLOAT” position and does not return.
Position (e): TILT
When  the  multi-function  mono-lever  is  pulled  further  from  the
“TILT” position, the lever stops in that position. When the buck-
et reaches the position preset by the bucket positioner, the lev-
er returns to the “HOLD” position.
Position (f): DUMP

KICKDOWN SWITCH

When traveling in forward 2nd, if kickdown switch (2) is press-
ed, the gear is shifted down to forward 1st.
Use this switch to increase the traction force during excavation.
When the transmission shift range (actual gear speed) is at for-
ward 1st (F1) and the power mode selector switch is set to E
mode, if the switch is pressed, the power mode changes to P
mode.
Use this switch to increase the traction force further during ex-
cavation or for scrape-up work.

In E mode

2nd

E mode

→

1st

E mode

→

1st

P mode

In P mode

2nd

P mode

→

1st

P mode

When the transmission is in the auto-shift mode and the travel speed is 10.5 km/h or slower, the kickdown
switch operates and the gear speed can be shifted down to 1st gear speed from any gear speed of the forward
or reverse travel.

HANDLE MULTIFUNCTION MONO-LEVER

ATTACHMENTS AND OPTIONS

6-4

«
...
402
403
404
405
406
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Jacobsen Страницы: 14

Бренд: Manitou Страницы: 156

Бренд: jcb Страницы: 208

BARKO LOADERS 275B SER-ERS

Бренд: Barko Hydraulics Страницы: 85

Бренд: BOXER Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды