Komatsu WA380-8 страница 198 Скачать руководство пользователя | Manualshive

Страница: 198 / 432

background image

REMARK

• Even if aftertreatment devices regeneration pilot lamp (1)

lights up, the machine does not need to be stopped and
the work can be continued, unless when the KDPF soot
accumulation caution lamp (2) lights up.

• Accumulation amount of soot can be checked by soot ac-

cumulation level (3) on the “Aftertreatment Devices Regen-
eration” screen.
Operate the menu switch on the standard screen to dis-
play the “Aftertreatment Devices Regeneration” screen.

• Automatic regeneration against accumulation of soot starts

when the soot accumulation level increases “3” or above,
and stops a while after the soot accumulation level de-
creases to “0”.

The  KDPF  regeneration  is  performed  automatically.  However,
the accumulated soot may not be burnt sufficiently and the fil-
tering  function  may  not  be  improved  under  certain  operating
conditions.
In  that  case,  KDPF  soot  accumulation  caution  lamp  (2)  lights
up. If this lamp lights up, stop the machine in a safe place and
perform the manual stationary regeneration.
For  details  of  the  procedure,  see  “PROCEDURE  FOR  MAN-
UAL STATIONARY REGENERATION (3-137)”.
Two types of monitor display require the manual stationary re-
generation, depending on the level of urgency.
When the directional lever is turned to NEUTRAL position (N)
and the parking brake switch is turned to the “PARKING” posi-
tion, the manual stationary regeneration may start automatical-
ly to protect the KDPF.

NOTICE
Do not stop engine when the aftertreatment devices regeneration is activated.
If KDPF soot accumulation caution lamp (2) is displayed, be sure to perform the manual stationary re-
generation.
When stopping the engine, stop the aftertreatment devices regeneration first according to “PROCE-
DURE FOR AFTERTREATMENT DEVICES REGENERATION DISABLE SETTING (3-139)”, then keep en-
gine running at low idle for approximately 5 minutes, and stop engine.
When the Action level “L03” lights up in red, and the KDPF soot accumulation caution lamp (2) lights up
in red, engine power deration is activated. To restore engine power, it is necessary to perform “PROCE-
DURE FOR MANUAL STATIONARY REGENERATION”.

EXPLANATION OF COMPONENTS

OPERATION

3-134

«
...
196
197
198
199
200
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Anderson Страницы: 162

PalletPal Stack-n-Go FPS2500-90 NAS

Бренд: Southworth Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды