Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 354 / 432

background image

1.

Start the engine and set the engine speed to approximate-
ly 1500 rpm.

2.

Press fan switch (1) and set the air flow to “Hi”.

3.

Press temperature adjustment switch (2) and set the tem-
perature to 18 °C.

4.

Fully open the doors and windows.

5.

Press air conditioner switch (3) to turn the air conditioner
switch ON.

6.

Check the condition of the refrigerant gas (chlorofluorocar-
bon 134a) that circulates the refrigerant circuit, through
sight glass (5) (inspection window) of air conditioner hose
(4).
A: Quantity of refrigerant
B: Condition viewed through sight glass
a: Appropriate: Just after the air conditioner switch is

turned ON, a small number of bubbles are seen. Then,
the sight glass becomes milky white, and then becomes
pale.

b: Insufficient: After the air conditioner switch is turned ON,

bubbles are seen continuously.

X: State of refrigerant flow
Y: Condition viewed through sight glass
x: Bubbles are seen: Gaseous and liquid refrigerants are

mixed.

y: No bubble: All refrigerant becomes liquid and transpar-

ent.

z: Milky white: Oil and refrigerant are separated and their

mixture is milky white.

MAINTENANCE AND SCHEDULE OF AIR CONDITIONER

Check point

Check items

Maintenance schedule

Check before

operation

6 months in-

spection

Replacement

interval

Filter

Clogging, dirt

Implement

-

2 years

Condenser

Clogging, dirt

Implement

-

-

Belt

Looseness, damage

Implement

-

2 years

Refrigerant gas

Charge amount

-

Implement

-

Piping

Looseness, damage,
leakage

-

Implement

-

Receiver drier

-

-

-

2 years

METHOD FOR REPLACING SLOW-BLOW FUSE

NOTICE

• When replacing the slow-blow fuse, be sure to turn the starting switch to OFF position and, after

confirming that the system operating lamp is not lit, set the battery disconnect switch key to OFF
position.

• Replace the slow blow fuse with the one of the same capacity.

Should the slow-blow fuse is blown, investigate the cause and take necessary actions.

MAINTENANCE PROCEDURE

MAINTENANCE

4-34

«
...
352
353
354
355
356
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Takeuchi Страницы: 265

Бренд: jcb Страницы: 18

Бренд: Toro Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды