Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 104 / 432

background image

REMARK

Display/Non-display of ECO guidance can be switched.
For the method of switching the display, see “SWITCH DISPLAY/NON-DISPLAY OF ECO GUIDANCE (3-60)”.

EXCESSIVE IDLING GUIDANCE

If the engine continues running idle for more than 5 minutes,
the excessive idling message is displayed on the monitor.
When waiting for work or taking short break, stop the engine to
reduce unnecessary fuel consumption.
When the accelerator pedal is depressed or the machine starts
traveling or the work equipment is operated, the excessive
idling message goes out.
For the auto idle stop function, see “AUTO IDLE STOP TIMER
SETTING (3-72)”.

GUIDANCE TO AVOID HYDRAULIC RELIEF

If the hydraulic equipment is relieved for more than 8 seconds
during operation, the hydraulic relief deterrence message is
displayed on the monitor.
The hydraulic equipment is relieved when an attempt is made
to lengthen each cylinder further over the maximum (for exam-
ple, to move bucket control lever to TILT while the bucket is
fully tilted) or reduce it further over the minimum.
Stop unnecessary relief.
The hydraulic relief deterrence message goes out automatically
after 10 seconds.

BRAKE DRAGGING PREVENTION GUIDANCE

If the accelerator pedal is depressed for more than 3 seconds
while applying the brake during traveling, the brake dragging
restriction message is displayed on the monitor.
If the accelerator is operated while the brake is used, fuel con-
sumption is increased.
The brake dragging prevention message goes out automatical-
ly after 10 seconds.

GUIDANCE OF ACCELERATOR PEDAL DEPRESSING LIMIT

If the accelerator pedal is depressed too much when the travel
direction  is  changed,  the  notification  of  accelerator  pedal  de-
pressing limit is displayed on the monitor.
In  order  to  reduce  fuel  consumption  during  directional  selec-
tion, try not to operate the accelerator pedal excessively.
The  notification  of  accelerator  pedal  depressing  limit  goes  out
automatically after 10 seconds.

EXPLANATION OF COMPONENTS

OPERATION

3-40

«
...
102
103
104
105
106
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

TASKMASTER 1350 PRO Series

Бренд: RAMROD Страницы: 37

IMPULSE IR LOADER

Бренд: TC Electronic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды