Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 39 / 432

background image

• Do not get on or off the machine with tools in your hand.

NO JUMPING ON OR OFF MACHINE

Getting on or off the moving machine can cause serious personal injury or death. Always observe the following.

• Never jump on or off the machine. Never get on or off a moving machine.
• If the machine starts to move when there is no operator on the machine, do not jump on to the machine and

try to stop it.

NO PEOPLE ON ATTACHMENTS

Never let anyone ride on the work equipment or other attachments. There is a hazard of falling and suffering
serious personal injury or death.

LIFTING OF PERSONNEL PROHIBITED

Under no circumstances should this machine be used for the lifting of personnel.

PRECAUTIONS WHEN STANDING UP FROM OPERATOR'S SEAT

When standing up from the operator's seat to adjust the opera-
tor's  seat,  be  sure  to  lower  the  work  equipment  completely  to
the  ground,  lock  the  work  equipment  by  pressing  work  equip-
ment lock switch (1) (pilot lamp lights up) and stop the engine
by  setting  parking  brake  switch  (2)  to  ON  (operation)  position
(A).
If  the  control  levers  are  touched  by  mistake,  there  is  danger
that  the  machine  may  suddenly  move  and  cause  serious  per-
sonal injury or death.

PRECAUTIONS WHEN LEAVING MACHINE

If the proper procedures are not taken when parking the machine, the machine may suddenly move off by itself,
and this may lead to serious personal injury or death. Always observe the following.

SAFETY

GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTE-

NANCE

2-19

«
...
37
38
39
40
41
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Genie Страницы: 64

Бренд: Case Страницы: 522

Бренд: jcb Страницы: 15

Бренд: Barko Страницы: 52

Бренд: Kubota Страницы: 2

Бренд: jcb Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды