Komatsu WA380-8 страница 167 Скачать руководство пользователя | Manualshive

Страница: 167 / 432

background image

Use  the  hazard  lamp  switch  when  you  need  to  park  the  ma-
chine  on  a  road  due  to  machine  failure  or  during  emergency
only.
Position  (A):  The  turn  signal  lamps  and  the  turn  signal  pilot

lamp flash.

Position (B):The lamps go out.

DIRECTIONAL SELECTOR SWITCH

(if equipped)
The directional selector switch is used to set the travel direction
to FORWARD, NEUTRAL, and REVERSE.
Position (F): FORWARD
Position (N): NEUTRAL
Position (R): REVERSE
Before using this switch to change the travel direction, set the
directional lever to NEUTRAL position and set the directional
selector enable switch of R.H. switch panel to “enable” position.

REMARK

Do not maintain the directional selector switch at the intermedi-
ate position between positions (F) and (N), or between posi-
tions (N) and (R). Such practice sounds the alarm buzzer and
sets the transmission in NEUTRAL.

TRANSMISSION CUT-OFF SWITCH

k

k

WARNING

When starting the machine off an uphill, turn the transmission cut-off switch to OFF position, depress
the accelerator pedal while depressing brake pedal and then release the brake pedal gradually to allow
the machine to start off. This prevents the machine from rolling back.

Press position (A) of the transmission cut-off switch to set it ON
or OFF.
If  you  release  your  hand  from  the  switch,  it  automatically  re-
turns to its original position.
Each time position (A) is pressed, the transmission cut-off func-
tion  switches  between  ON  and  OFF.  When  this  function  is
turned on, the pilot lamps light up on the monitor and on switch
(A)  position,  and  the  transmission  becomes  NEUTRAL  at  the
adjusted brake pedal pressing position.
Normally, keep the switch at ON position.
For  details  of  the  cut-off  position  adjustment  procedure,  see  “METHOD  FOR  ADJUSTING  TRANSMISSION
CUT-OFF POSITION (3-199)”.

TRANSMISSION CUT-OFF SET SWITCH

k

k

CAUTION

Apply the parking brake, before starting adjustment of the transmission cut-off position.

OPERATION

EXPLANATION OF COMPONENTS

3-103

«
...
165
166
167
168
169
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Takeuchi Страницы: 170

Бренд: Takeuchi Страницы: 182

Бренд: AVANT Страницы: 8

Бренд: AVANT Страницы: 108

Бренд: Terex Страницы: 83

PT100G Forestry

Бренд: Terex Страницы: 142

Бренд: SUNWARD Страницы: 55

Бренд: Doosan Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды