Komatsu WA380-8 страница 357 Скачать руководство пользователя | Manualshive

Страница: 357 / 432

background image

METHOD FOR CHECKING AND INFLATING TIRE

k

k

WARNING

• When pumping up the tires, check that no other person is standing near the tire, and install an air

chuck with a clip that can be secured to the air valve.

• To prevent the tire inflation pressure from becoming too high, measure the pressure from time to

time with an air gauge while pumping up the tire.

• When it is inflated, the rim parts may fly out, if they are not fitted properly.

Put a fence around the tire for protection. The worker must not stand in front of the rim but must
stand on the tread side during work.

• Abnormal drop of inflation pressure and abnormal fitting of the rim indicate a trouble in the tire or

rim. In this case, be sure to ask a tire repair shop for repair.

• Be sure to observe the specified inflation pressure.
• Do not adjust the tire inflation pressure immediately after traveling at high speed or operating under

heavy load.

Check the tire inflation pressure before starting work while the tires are cold.
When inflating a tire, use an air chuck which can be fixed to the air valve of the tire as shown in the figure.
Do not work in front of the rim but work on the tread side of the
tire.

1.

Measure the inflation pressure with a tire inflation pressure gauge.

2.

Adjust the inflation pressure properly.
The proper inflation pressure is shown below.

Tire size

Standard inflation pressure

Standard

23.5R25

☆

Front wheel: 400 kPa {4.0 kg/cm

2

}

Rear wheel: 400 kPa {4.0 kg/cm

2

}

Optional

23.5-25-16PR

Front wheel: 310 kPa {3.1 kg/cm

2

}

Rear wheel: 310 kPa {3.1 kg/cm

2

}

NOTICE
Appropriate inflation pressure varies depending on the given type of work. For details, see “TIRES
(2-42)”.

METHOD FOR CLEANING AND REPLACING FUEL TANK BREATHER ELEMENT

k

k

CAUTION

If you inspect or clean while engine is running, dirt enters the fuel tank and damages the engine.
Be sure to stop the engine before performing these works.

MAINTENANCE

MAINTENANCE PROCEDURE

4-37

«
...
355
356
357
358
359
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Great Bend 1045

Бренд: Bush Hog Страницы: 1

Бренд: Genie Страницы: 64

Бренд: Cub Cadet Страницы: 2

Бренд: Terex Страницы: 87

Бренд: Terex Страницы: 114

Бренд: Hyundai Страницы: 415

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды