Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 55 / 432

background image

• Set frame lock bar (4) to LOCK position (L) to lock the front

and rear frame.

• After opening the rear full-length fender, set lock lever (5)

to LOCK position (L).

TWO WORKERS FOR MAINTENANCE WHEN ENGINE IS RUNNING

To prevent accident, do not perform maintenance with the engine running. When it is necessary to perform the
maintenance with the engine running, always observe the following.

• One worker must always sit in the operator's seat and be ready to stop the engine at any time. All workers

must maintain contact with the other workers.

• Rotating parts such as the fan, fan belt are dangerous that

they may easily catch a body part or an object someone
wears. Be careful not to come close to the rotating part.

• Never drop or insert tools or other objects into the fan, fan

belt, or other rotating parts. They may contact the rotating
parts and break, and be scattered. It is dangerous.

• If the automatic active regeneration of KDPF starts during

maintenance work, surroundings of KDPF become high
temperature.
When performing maintenance work, perform the after-
treatment devices regeneration disable according to “HAN-
DLE Komatsu Diesel Particulate Filter (KDPF) (3-133)”.

• Lower the work equipment to the ground and press work

equipment lock switch (1) to lock the work equipment (pilot
lamp lights up) and prevent it from moving.

,&

SAFETY

PRECAUTIONS FOR MAINTENANCE

2-35

«
...
53
54
55
56
57
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: RHINO Страницы: 4

Бренд: RHINO Страницы: 44

Бренд: RHINO Страницы: 100

Бренд: RHINO Страницы: 104

Бренд: RHINO Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды