Komatsu WA380-8 страница 235 Скачать руководство пользователя | Manualshive

Страница: 235 / 432

background image

3.

When  the  machine  is  equipped  with  the  secondary  steer-
ing,  it  performs  self  check  approximately  3  seconds  after
the starting switch is turned to ON position.
At  this  time,  the  steering  oil  pressure  caution  lamp  (red)
and  the  secondary  steering  pilot  lamp  light  up  simultane-
ously.
If  the  machine  does  not  perform  the  self  check  or  the
above  lamps  do  not  light  up,  there  may  be  a  failure.  Ask
your Komatsu distributor for inspection.

Check of the secondary steering is not performed in the following cases.

• When you have turned the starting switch to ON position and, without starting the engine, turned it to OFF

position then turned it to ON position again.

• When you have turned the starting switch to ON position again immediately after the engine is stopped

when the steering pressure is not completely lowered.

• When the engine preheating is in operation.

METHOD FOR CHECKING HORN

Operate the horn switch and check that the horn sounds.
If there is any abnormality, ask your KOMATSU distributor for testing and repair.

METHOD FOR CHECKING DEFROSTER FUNCTION

• Operate the air conditioner and check that the air flows out of the vents properly onto the front glass.

If there is any abnormality, ask your KOMATSU distributor for testing and repair.

• Operate the rear heated wire glass switch and check that the rear glass surface is heated properly.

If there is any abnormality, ask your KOMATSU distributor for testing and repair.

METHOD FOR CHECKING LOCKS

Check that all places can be locked properly.
(For the locations of the locks, see “LOCK (3-220)”.)
If there is any abnormality, ask your KOMATSU distributor for testing and repair.

METHOD FOR CHECKING ALTERNATE EXIT OF CAB

Operate the open knob for alternate exit of cab, and check that the exit opens and closes properly.
If there is any abnormality, ask your KOMATSU distributor for testing and repair.

METHOD FOR ADJUSTING
METHOD FOR ADJUSTING OPERATOR'S SEAT

k

k

WARNING

• Place the machine in a safe place when adjusting the position of the operator's seat.

Always set the work equipment lock lever to LOCK position (the pilot lamp in the switch is lit) to
prevent any accidental contact with the control levers.

• Adjust it before starting operation or when operators change shift.
• Adjust the position of the operator's seat so that you can depress the brake pedal fully with your

back against the seat backrest.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-171

«
...
233
234
235
236
237
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Case Страницы: 61

Бренд: Allied Страницы: 46

TLB25-35BV Series

Бренд: Scag Power Equipment Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды