manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 93

WATER SEPARATOR CAUTION LAMP

The water separator caution lamp warns that water is accumu-
lated in the water separator.
When  water  is  accumulated  in  the  water  separator,  the  lamp
lights up in red.
Stop the engine and drain the water separator.
For details, see “METHOD FOR CHECKING WATER SEPARA-
TOR, DRAINING WATER AND SEDIMENT (3-162)”.

REMARK

The water separator forms one unit with the fuel prefilter.
The water separator is installed at the bottom of the fuel prefil-
ter as detachable condition.

AIR CLEANER CLOGGING CAUTION LAMP

Air cleaner clogging caution lamp warns about clogging of the
air cleaner.
If the caution lamp lights up in yellow and action level “L01” is
displayed,  stop  the  engine,  then  inspect  and  clean  the  air
cleaner.
See  “METHOD  FOR  CHECKING,  CLEANING  AND  REPLAC-
ING AIR CLEANER (4-14)”.

FAN CONTROL SYSTEM CAUTION LAMP

The fan control system caution lamp warns about abnormality
in the fan control system.

• When action level “L03” is displayed

The lamp lights up in red. At the same time, the centralized
warning lamp lights up and alarm buzzer sounds intermit-
tently.
Stop  the  operation,  move  the  machine  to  a  safe  place,
stop the engine, then ask your Komatsu distributor for in-
spection and maintenance.

• When action level “L01” is displayed

The lamp lights up in yellow.
When you finish the operation, always perform the inspection and maintenance.
Ask your Komatsu distributor for the inspection and maintenance as needed.

AIR CONDITIONER SYSTEM CAUTION LAMP

Air conditioner system caution lamp warns about abnormality in
air conditioner system.
If  the  lamp  lights  up  in  yellow  and  action  level  “L01”  is  dis-
played,  always  perform  inspection  and  maintenance  after  the
operation is finished.
Ask  your  Komatsu  distributor  for  the  inspection  and  mainte-
nance as needed.

OPERATION

EXPLANATION OF COMPONENTS

3-29

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды