ITT Goulds Pumps IC Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 97

background image

NOTICE:

The mechanical seal must have an appropriate seal-flush system. Failure to do so will

result in excess heat generation and seal failure.

6.6.3.1 Seal the shaft with a packed stuffing box

WARNING:

Packed stuffing boxes are not allowed in an ATEX-classified environment.

WARNING:

Failure to disconnect and lock out driver power may result in serious physical injury. Never
attempt to replace the packing until the driver is properly locked out.

Pumps are shipped without the packing, lantern ring, or split gland installed. These parts are included
with the box of fittings shipped with each pump and must be installed before startup.

1.

Carefully clean the stuffing-box bore.

2.

Twist the packing enough to get it around the shaft.

Packing rings

Lantern rings

1

3

4

2

3

4

1.

Packing rings

2.

Lantern rings

3.

Correct

4.

Incorrect

Figure 54: Packing rings and lantern rings

3.

Insert the packing and stagger the joints in each ring by 90°.
Install the stuffing-box parts in this order:

a) One packing ring

b) One lantern ring (two-piece)

c)

Three packing rings

NOTICE:

Make sure that the lantern ring is located at the flushing connection to ensure that flush is
obtained. Failure to do so may result in decreased performance.

4.

Install the gland halves and evenly hand-tighten the nuts .

6.6.3.2 Seal the shaft with a cartridge mechanical seal

WARNING:

The mechanical seal used in an Ex-classified environment must be properly certified.

6.6 Reassembly

82

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

«
...
82
83
84
85
86
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

JABSCO 11860 Series

Бренд: Xylem Страницы: 24

Бренд: Graco Страницы: 48

Бренд: Rinnai Страницы: 2

HYDROMATIC G2HX

Бренд: Pentair Страницы: 12

Бренд: Gardenline Страницы: 28

Бренд: Endress Страницы: 17

Бренд: F.F. Group Страницы: 28

Бренд: Daikin Страницы: 44

Бренд: Binks Страницы: 22

Mainsboost Plus

Бренд: Stuart Turner Страницы: 28

Бренд: Debem Страницы: 68

Бренд: Bradford White Страницы: 21

Бренд: IPM Страницы: 24

Бренд: Wilo Страницы: 16

Бренд: ubbink Страницы: 30

Бренд: E-gas Страницы: 10

Бренд: Varian Страницы: 53

Бренд: Whale Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды