ITT Goulds Pumps IC Скачать руководство пользователя страница 44

Страница: 44 / 97

Check

Explanation/comment

Checked

Assure adequate insulation is applied for
liquids with specific gravity less than
0.60.

To assure sufficient NPSHa.

Liquid source below the pump

Check

Explanation/comment

Checked

Make sure that the suction piping is free
from air pockets.

This helps to prevent the occurrence of air and cavi-
tation in the pump inlet.

Check that the suction piping slopes up-
wards from the liquid source to the pump
inlet.

—

If the pump is not self-priming, check that
a device for priming the pump is instal-
led.

Use a foot valve with a diameter that is at least
equivalent to the diameter of the suction piping.

Liquid source above the pump

Check

Explanation/comment

Checked

Check that an isolation valve is installed
in the suction piping at a distance of at
least two times the pipe diameter from
the suction inlet.

This permits you to close the line during pump in-
spection and maintenance.

Do not use the isolation valve to throttle the pump.
Throttling can cause these problems:

•

Loss of priming

•

Excessive temperatures

•

Damage to the pump

•

Voiding the warranty

Make sure that the suction piping is free
from air pockets.

This helps to prevent the occurrence of air and cavi-
tation in the pump inlet.

Check that the piping is level or slopes
downward from the liquid source.

—

Make sure that no part of the suction pip-
ing extends below the suction flange of
the pump.

—

Make sure that the suction piping is ade-
quately submerged below the surface of
the liquid source.

This prevents air from entering the pump through a
suction vortex.

Example: Elbow close to the pump suction inlet

Correct

Incorrect

The correct distance between the inlet flange of the
pump and the closest elbow must be at least five pipe
diameters.

Enough distance to prevent cavitation

Eccentric reducer with a level top

4.6 Piping checklists

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды