ITT Goulds Pumps IC Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 97

background image

NOTICE:

Grease can settle in equipment left idle leaving bearings improperly lubricated. Check the
greasing on a pump that has been out of service for a long period of time and re-grease if
necessary.

Pumps are shipped without oil. You must lubricate oil-lubricated bearings at the job site.

Grease-lubricated bearings are lubricated at the factory.

The bearing manufacturer fills greased-for-life bearings with grease and seals them at the factory.
You do not need to lubricate or seal these bearings.

5.6.1 Lubricating oil requirements

Oil quality requirements

Use a high-quality turbine oil with rust and oxidation inhibitors.

Lubricating oil type

•

CLP46

•

DIN 51517

•

HD 20W/20 SAE

Symbol

DIN 51502

Kinematic viscosity at 40°C | 104°F

46 ±4 mm

2

/sec |

0.0713 ±0.006 in.

2

/sec

Flash point (Cleveland)

175°C | 347°F

Setting point (Pourpoint)

-15°C | 5°F

Application temperature

(Contact your ITT representative to determine a suita-
ble type of lubrication if ambient temperatures are be-
low -10°C | 14°F.

Higher than permitted bearing temperature

Oil quantity requirements

Bearing frame size

Oil quantity in liters | quarts

24

0.5 | 0.53

32

1.1 | 1.16

42

1.4 | 1.48

48

1.7 | 1.8

5.6.2 Lubricate the bearings with oil

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. En-

sure bearings are properly lubricated prior to startup.

NOTICE:

The pump is not filled with oil when delivered. Fill with oil before operating the pump.

•

Determine which procedure to use in order to fill the bearing frame with oil:

If...

Then...

The pump has an oil level sight glass (stand-
ard design)

Use the "Fill the bearing frame with oil" proce-
dure.

The pump has a constant level oiler (option-
al)

Use the "Fill the bearing frame with an optional
oiler" procedure.

5.6 Bearing lubrication

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

53

«
...
53
54
55
56
57
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: Lamborghini Caloreclima Страницы: 192

Бренд: TradeQuip Страницы: 8

Бренд: EINHELL Страницы: 44

Бренд: Campbell Страницы: 2

Бренд: T.I.P. Страницы: 136

Бренд: Daikin Страницы: 24

Бренд: Ducar Страницы: 30

Бренд: Zip Страницы: 24

THBF701 Master Series

Бренд: bluefin Страницы: 17

Бренд: Newton Страницы: 4

Бренд: Laars Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды