ITT Goulds Pumps IC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 97

background image

1 Introduction and Safety

1.1 Introduction

Purpose of this manual

The purpose of this manual is to provide necessary information for:

•

Installation

•

Operation

•

Maintenance

CAUTION:

Failure to observe the instructions contained in this manual could result in personal injury
and/or property damage, and may void the warranty. Read this manual carefully before in-
stalling and using the product.

NOTICE:

Save this manual for future reference and keep it readily available.

1.1.1 Requesting other information

Special versions can be supplied with supplementary instruction leaflets. See the sales contract for
any modifications or special version characteristics. For instructions, situations, or events that are not
considered in this manual or in the sales documents, please contact the nearest ITT representative.

Always specify the exact product type and identification code when requesting technical information
or spare parts.

1.2 Safety

WARNING:

•

Risk of serious personal injury. Applying heat to impellers, propellers, or their retaining
devices can cause trapped liquid to rapidly expand and result in a violent explosion.
This manual clearly identifies accepted methods for disassembling units. These meth-
ods must be adhered to. Never apply heat to aid in their removal unless explicitly stat-
ed in this manual.

•

The operator must be aware of the pumpage and take appropriate safety precautions
to prevent physical injury.

•

Risk of serious injury or death. If any pressure-containing device is over-pressurized,
it can explode, rupture, or discharge its contents. It is critical to take all necessary
measures to avoid over-pressurization.

•

Risk of death, serious personal injury, and property damage. Installing, operating, or
maintaining the unit using any method not prescribed in this manual is prohibited. Pro-
hibited methods include any modification to the equipment or use of parts not provid-
ed by ITT. If there is any uncertainty regarding the appropriate use of the equipment,
please contact an ITT representative before proceeding.

•

If the pump or motor is damaged or leaking, electric shock, fire, explosion, liberation
of toxic fumes, physical harm, or environmental damage may result. Do not operate
the unit until the problem has been corrected or repaired.

•

Risk of serious personal injury or property damage. Dry running may cause rotating
parts within the pump to seize to non-moving parts. Do not run dry.

1 Introduction and Safety

4

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

«
...
4
5
6
7
8
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Danfoss Страницы: 72

Бренд: RAASM Страницы: 72

Бренд: Water Factory Systems Страницы: 15

Бренд: Waterous Страницы: 10

Бренд: Oasis Страницы: 18

Бренд: SAER Elettropompe Страницы: 36

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: Calpeda Страницы: 72

LEADER ECOTRONIC Series

Бренд: DAB PUMPS Страницы: 10

Бренд: Bryant Страницы: 26

Бренд: Edwards Страницы: 16

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

Бренд: Dantherm Страницы: 17

Бренд: GilAir Plus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды