ITT Goulds Pumps IC Скачать руководство пользователя страница 66

Страница: 66 / 97

Replace worn parts.

6.2 Bearing maintenance

These bearing lubrication sections list different temperatures of pumped fluid. If your pump is

ATEX certified and the pumped fluid exceeds the permitted temperature values, then consult your
ITT representative.

Bearing lubrication schedule

Type of bearing

First lubrication

Lubrication intervals

Oil-lubricated bearings Add oil before you install and start the

pump.

Change the oil after 200-300 hours of op-
eration, depending on bearing tempera-
ture.

See the Oil change schedule table.

Grease-lubricated
bearings

N/A

Every 4000 hours of operation or once a
year, whichever comes first

Every two years if the pump is left idle

Oil change schedule

Oil must be changed at least once a year.

Bearing temperature

First oil change

Subsequent oil changes

Up to 60°C | 140°F

After 300 hours of operation Every 8760 hours of operation

60°C to 80°C | 140°F to 176°F After 300 hours of operation Every 4000 hours of operation
80°C to 100°C | 176°F to 212°F After 200 hours of operation Every 3000 hours of operation

NOTICE:

•

Strictly maintain the oil changing schedule if the pump is operating in an potentially
explosive environment.

•

Change the oil every two years if the pump is left idle.

•

Dispose of used oil in accordance with local environmental regulations.

6.2.1 Lubricating oil requirements

Oil quality requirements

Use a high-quality turbine oil with rust and oxidation inhibitors.

Lubricating oil type

•

CLP46

•

DIN 51517

•

HD 20W/20 SAE

Symbol

DIN 51502

Kinematic viscosity at 40°C | 104°F

46 ±4 mm

/sec |

0.0713 ±0.006 in.

/sec

Flash point (Cleveland)

175°C | 347°F

Setting point (Pourpoint)

-15°C | 5°F

Application temperature

(Contact your ITT representative to determine a suita-
ble type of lubrication if ambient temperatures are be-
low -10°C | 14°F.

Higher than permitted bearing temperature

6.2 Bearing maintenance

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды