ITT Goulds Pumps IC Скачать руководство пользователя страница 33

Страница: 33 / 97

Guideline

Explanation

Move or shim only the driver in order to make adjustments.

This prevents strain on the piping installa-
tions.

Make sure that the hold-down bolts for the driver are tight when
you take indicator measurements.

This keeps the driver stationary since move-
ment causes incorrect measurement.

Make sure that the hold-down bolts for the driver are loose be-
fore you make alignment corrections.

This makes it possible to move the driver
when you make alignment corrections.

Check the alignment again after any mechanical adjustments.

This corrects any misalignments that an ad-
justment may have caused.

4.4.4 Attach the dial indicators for alignment

You must have two dial indicators in order to complete this procedure.

Attach two dial indicators on the pump coupling half (X):

a) Attach one indicator (P) so that the indicator rod comes into contact with the perimeter of

the driver coupling half (Y).

This indicator is used to measure parallel misalignment.

b) Attach the other indicator (A) so that the indicator rod comes into contact with the inner end

of the driver coupling half.

This indicator is used to measure angular misalignment.

Figure 13: Dial indicator attachment

Rotate the pump coupling half (X) in order to check that the indicators are in contact with the
driver coupling half (Y) but do not bottom out.

Adjust the indicators if necessary.

4.4.5 Pump-to-driver alignment instructions

4.4.5.1 Perform angular alignment for a vertical correction

Set the angular alignment indicator to zero at the top-center position (12 o’clock) of the driver
coupling half (Y).

Rotate the indicator to the bottom-center position (6 o’clock).

Record the indicator reading.

When the
reading val-
ue is...

Then...

Negative

The coupling halves are farther apart at the bottom than at the top. Perform one of
these steps:

•

Add shims in order to raise the feet of the driver at the shaft end.

•

Remove shims in order to lower the feet of the driver at the other end.

4.4 Pump-to-driver alignment

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды