ITT Goulds Pumps IC Скачать руководство пользователя страница 26

Страница: 26 / 97

Item Description

Machinist's levels

Driver's mounting pads

Foundation bolts

Jackscrews

Grout hole

Pump's mounting pads

Figure 9: Level driver mounting pads

Turn the center jackscrews down so that they rest on their plates on the foundation surface.

Level the pump mounting pads:

NOTICE:

Remove all dirt from the mounting pads in order to ensure that the correct leveling is ach-
ieved. Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.

b) Put the other level across the center of the two pads.

Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both lengthwise
and across.

Item Description

Driver's mounting pads

Machinist's levels

Foundation bolts

Jackscrews

Grout hole

Pump's mounting pads

Figure 10: Level pump mounting pads

Hand-tighten the nuts for the foundation bolts.

Check that the driver's mounting pads are level and adjust the jackscrews and the foundation
bolts if necessary.

The correct level measurement is a maximum of 0.167 mm/m | 0.002 in./ft .

4.2 Baseplate-mounting procedures

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды