ITT Goulds Pumps IC Скачать руководство пользователя страница 92

Страница: 92 / 97

7.3 Assembly troubleshooting

Symptom

Cause

Remedy

There is excessive shaft end play.

The internal clearance of the bearings
exceeds the recommended amount.

Replace the bearings with a
bearing of the correct type.

The snap ring is loose in the bearing-
housing groove.

Re-seat the snap ring.

There is excessive shaft and sleeve
runout.

The sleeve is worn.

Replace the sleeve.

The shaft is bent.

Replace the shaft.

There is excessive bearing-frame
flange runout.

The shaft is bent.

Replace the shaft.

The flange of the bearing frame is dis-
torted.

Replace the bearing-frame
flange.

There is excessive frame-adapter run-
out.

There is corrosion on the frame
adapter.

Replace the frame adapter.

The adapter-to-frame gasket is not
seated properly.

Re-seat the frame adapter and
make sure that the adapter-to-
frame gasket is seated properly.

There is excessive seal chamber or
stuffing-box cover runout.

The seal chamber or the stuffing-box
cover is not properly seated in the
frame adapter.

Re-seat the seal chamber or
stuffing-box cover.

There is corrosion or wear on the seal
chamber or stuffing-box cover.

Replace the seal chamber or
stuffing-box cover.

There is excessive vane-tip runout of
the impeller.

The vane is bent.

Replace the impeller.

7.3 Assembly troubleshooting

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды