ITT Goulds Pumps IC Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 97

background image

•

Protective shoes

•

Protective gloves

•

Gas mask

•

Hearing protection

•

First-aid kit

•

Safety devices

Electrical connections

Electrical connections must be made by certified electricians in compliance with all international, na-
tional, state, and local regulations. For more information about requirements, see sections dealing
specifically with electrical connections.

1.2.3.1 Precautions before work

Observe these safety precautions before you work with the product or are in connection with the
product:

•

Provide a suitable barrier around the work area, for example, a guard rail.

•

Make sure that all safety guards are in place and secure.

•

Make sure that you have a clear path of retreat.

•

Make sure that the product cannot roll or fall over and injure people or damage property.

•

Make sure that the lifting equipment is in good condition.

•

Use a lifting harness, a safety line, and a breathing device as required.

•

Allow all system and pump components to cool before you handle them.

•

Make sure that the product has been thoroughly cleaned.

•

Disconnect and lock out power before you service the pump.

•

Check the explosion risk before you weld or use electric hand tools.

1.2.3.2 Precautions during work

Observe these safety precautions when you work with the product or are in connection with the prod-
uct:

CAUTION:

Failure to observe the instructions contained in this manual could result in personal injury
and/or property damage, and may void the warranty. Read this manual carefully before in-
stalling and using the product.

•

Never work alone.

•

Always wear protective clothing and hand protection.

•

Stay clear of suspended loads.

•

Always lift the product by its lifting device.

•

Beware of the risk of a sudden start if the product is used with an automatic level control.

•

Beware of the starting jerk, which can be powerful.

•

Rinse the components in water after you disassemble the pump.

•

Do not exceed the maximum working pressure of the pump.

•

Do not open any vent or drain valve or remove any plugs while the system is pressurized. Make
sure that the pump is isolated from the system and that pressure is relieved before you disas-
semble the pump, remove plugs, or disconnect piping.

•

Never operate a pump without a properly installed coupling guard.

•

The coupling guard used in an ATEX classified environment must be constructed from a non-

sparking material.

1.2 Safety

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

7

«
...
7
8
9
10
11
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Davey Страницы: 12

Бренд: Barmesa Pumps Страницы: 42

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: Lamborghini Caloreclima Страницы: 192

Бренд: Walrus Pump Страницы: 8

Xsential QUAD-RO

Бренд: Watermark Страницы: 8

Бренд: Wilo Страницы: 76

Бренд: BLACKMER Страницы: 12

Бренд: Calorex Страницы: 2

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

Бренд: Hoshizaki Страницы: 10

Бренд: Watson-Marlow Страницы: 12

XC Filter Cartridge EV9613-09

Бренд: Everpure Страницы: 2

AQUARAIN RJ 5.60.1M

Бренд: OLIJU Страницы: 24

Бренд: D-D The Aquarium Solution Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды