ITT Goulds Pumps IC Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 97

background image

4 Installation

4.1 Pre-installation

Precautions

WARNING:

•

When installing in a potentially explosive environment, ensure that the motor is prop-
erly certified.

•

All equipment being installed must be properly grounded to prevent unexpected dis-
charge. Discharge can cause equipment damage, electric shock, and result in serious
injury. Test the ground lead to verify it is connected correctly.

NOTICE:

•

Electrical connections must be made by certified electricians in compliance with all in-
ternational, national, state and local regulations.

•

Supervision by an authorized ITT representative is recommended to ensure proper in-
stallation. Improper installation may result in equipment damage or decreased per-
formance.

4.1.1 Pump location guidelines

WARNING:

Safe lifting points are specifically identified in this manual. It is critical to lift the equipment
only at these points. Integral lifting eyes or eye bolts on pump and motor components are
intended for use in lifting the individual components only.

WARNING:

Assembled units and their components are heavy. Failure to properly lift and support this
equipment can result in serious physical injury and/or equipment damage. Lift equipment
only at the specifically identified lifting points. Lifting devices such as swivel hoist rings,
shackles, slings and spreaders must be rated, selected, and used for the entire load being
lifted.

Guideline

Explanation/comment

Keep the pump as close to the liquid source as
practically possible.

This minimizes the friction loss and keeps the suction piping
as short as possible.

Make sure that the space around the pump is
sufficient.

This facilitates ventilation, inspection, maintenance, and serv-
ice.

If you require lifting equipment such as a hoist or
tackle, make sure that there is enough space
above the pump.

This makes it easier to properly use the lifting equipment and
safely remove and relocate the components to a safe loca-
tion.

Protect the unit from weather and water damage
due to rain, flooding, and freezing temperatures.

This is applicable if nothing else is specified.

4 Installation

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

19

«
...
19
20
21
22
23
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: TANKLESS Страницы: 72

S15 Non-Metallic

Бренд: Sandpiper Страницы: 25

Бренд: A.O. Smith Страницы: 2

Residential Gas Water Heaters

Бренд: A.O. Smith Страницы: 84

Бренд: Goodman Страницы: 16

Бренд: P.Lindberg Страницы: 46

AquaMax Eco Expert 20000/12V

Бренд: Oase Страницы: 231

Бренд: Zodiac Страницы: 36

Comfort 5000/5 LCD

Бренд: Gardena Страницы: 13

Бренд: GilAir Plus Страницы: 4

Бренд: Samoa Страницы: 32

Бренд: Atlantic Страницы: 24

Бренд: Hozelock Страницы: 6

DHE?18 SLi 25 A

Бренд: STIEBEL ELTRON Страницы: 22

Quick-Fill 58609

Бренд: Intex Страницы: 5

AquaMax Eco Expert 5300

Бренд: Oase Страницы: 20

Бренд: Sulzer Страницы: 16

Бренд: Barmesa Pumps Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды