ITT Goulds Pumps IC Скачать руководство пользователя страница 22

Страница: 22 / 97

Guideline

Explanation/comment

Do not install and operate the equipment in
closed systems unless the system is constructed
with properly-sized safety devices and control
devices.

Acceptable devices:

•

Pressure relief valves

•

Compression tanks

•

Pressure controls

•

Temperature controls

•

Flow controls

If the system does not include these devices, consult the en-
gineer or architect in charge before you operate the pump.

Take into consideration the occurrence of un-
wanted noise and vibration.

The best pump location for noise and vibration absorption is
on a concrete floor with subsoil underneath.

If the pump location is overhead, undertake spe-
cial precautions to reduce possible noise trans-
mission.

Consider a consultation with a noise specialist.

4.1.2 Foundation requirements

Requirements

•

The location and size of the foundation bolt holes must match those shown on the assembly
drawing provided with the pump data package.

•

The foundation must weigh between two and three times the weight of the pump.

•

Provide a flat, substantial concrete foundation in order to prevent strain and distortion when you
tighten the foundation bolts.

•

The concrete foundation must have sufficient firmness according to DIN 1045 or equal stand-
ard.

Sleeve-type bolts

Item Description

Baseplate

Shims

Foundation

Sleeve

Dam

Bolt

Figure 4: Sleeve type bolts

4.1 Pre-installation

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды