ITT Goulds Pumps IC Скачать руководство пользователя страница 12

Страница: 12 / 97

CSA certification

Intrinsically safe for:

•

Class I, Div. 1, Groups A, B, C, D

•

Class II, Div. 1, Groups E, F, G

•

Class III

•

Certified to Canadian and US requirements

SERIAL NO. & YEAR OF
MANUFACTURE HERE.

1.4 Product warranty

Coverage

ITT undertakes to remedy faults in products from ITT under these conditions:

•

The faults are due to defects in design, materials, or workmanship.

•

The faults are reported to an ITT representative within the warranty period.

•

The product is used only under the conditions described in this manual.

•

The monitoring equipment incorporated in the product is correctly connected and in use.

•

All service and repair work is done by ITT-authorized personnel.

•

Genuine ITT parts are used.

•

Only Ex-approved spare parts and accessories authorized by ITT are used in Ex-approved
products.

Limitations

The warranty does not cover faults caused by these situations:

•

Deficient maintenance

•

Improper installation

•

Modifications or changes to the product and installation made without consulting ITT

•

Incorrectly executed repair work

•

Normal wear and tear

ITT assumes no liability for these situations:

•

Bodily injuries

•

Material damages

•

Economic losses

Warranty claim

ITT products are high-quality products with expected reliable operation and long life. However,
should the need arise for a warranty claim, then contact your ITT representative.

1.4 Product warranty

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды