ITT Goulds Pumps IC Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 97

background image

6.6.2 Install the impeller

CAUTION:

Risk of physical injury from sharp edges. Wear heavy work gloves when handling impellers.

For the fitting threads and for tight tolerances, use a suitable anti-seize compound. Use this, for ex-
ample, between the shaft sleeve and the shaftmotor shaft and pump shaft or between the impeller
and the shaft. This makes the assembly and the next disassembly easier to perform.

NOTICE:

Anti-seize compounds must be compatible with the pumped fluid.

Perform these steps in order to install the impeller:

1.

Insert the impeller key (940.31) in the shaft (210).

2.

Slide the impeller (230) onto the shaft.

3.

Secure the rotor at the coupling end and tighten the impeller nut (922) (right-threaded).

4.

Tighten the impeller nut to the torques listed in the Torque values table.

922

412.21

230

210

940.31

Figure 53: Impeller installation

NOTICE:

Crush hazard. Make sure that the back pull-out assembly cannot tip over.

6.6.3 Shaft sealing

WARNING:

The mechanical seal used in an Ex-classified environment must be properly certified.

CAUTION:

Running a mechanical seal dry, even for a few seconds, can cause seal failure and physi-
cal injury. Never operate the pump without liquid supplied to the mechanical seal.

Before proceeding with seal installation, complete the ICO assembly worksheet on shim measure-
ment method and installation. Follow Seal the shaft with a cartridge mechanical seal.

6.6 Reassembly

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

81

«
...
81
82
83
84
85
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Eagle Страницы: 16

Бренд: Danfoss Страницы: 72

Бренд: Rheem Страницы: 15

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Бренд: Amtrol Страницы: 2

AquaSurge PRO 2000-4000

Бренд: Aquascape Pro Страницы: 8

Бренд: York Страницы: 12

Бренд: Santon Страницы: 20

Бренд: CareFusion Страницы: 28

Бренд: Carlisle Fluid Technologies Страницы: 40

Бренд: emaux Страницы: 21

Бренд: American Water Heater Страницы: 60

WMMS -18EC-V2B2

Бренд: YMGI Страницы: 48

Бренд: DAYLIFF Страницы: 12

Viscount I 1000

Бренд: Graco Страницы: 16

Бренд: Makita Страницы: 109

Бренд: Super Guider Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды