ITT Goulds Pumps IC Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 97

background image

4.2.5 Install the baseplate using spring mounting

NOTICE:

The spring-mounted baseplate is designed only to support piping loads from thermal ex-
pansion. Ensure that the suction and discharge piping are supported individually. Failure to
do so may result in equipment damage.

The foundation pads are not provided with the baseplate. Make sure that the foundation pads are
316 stainless-steel plates, which have a 16-20 micro-inch surface finish.

Before you start this procedure, make sure that the foundation pads are correctly installed on the
foundation/floor (see the manufacturer's instructions).

1.

Put the baseplate on a support above the foundation/floor.
Make sure that there is enough space between the baseplate and the foundation/floor in order
to install the spring assemblies.

2.

Install the lower part of the spring assembly:

a) Screw the lower jam nut onto the spring stud.

b) Screw the lower adjusting nut onto the spring-stud, on top of the jam nut.

c)

Set the lower adjusting nut to the correct height.

The correct height depends on the required distance between the foundation/floor and the base-
plate.

d) Put a washer, a follower, a spring, and one more follower onto the lower adjusting nut.

3.

Install the spring assembly on the baseplate:

a) Insert the spring assembly into the baseplate's anchorage hole from below.

b) Put a follower, a spring, another follower, and a washer onto the spring stud.

c)

Fasten the spring assembly with the upper adjusting nut by hand.

4.

Thread the upper jam nut onto the spring stud by hand.

5.

Repeat steps 2 through 4 for all the spring assemblies.

6.

Lower the baseplate so that the spring assemblies fit into the foundation pads.

7.

Level the baseplate and make the final height adjustments:

a) Loosen the upper jam nuts and adjusting nuts.

b) Adjust the height and level the baseplate by moving the lower adjusting nuts.

c)

When the baseplate is level, tighten the top adjusting nuts so that the top springs are not
loose in their followers.

8.

Fasten the lower and upper jam nuts on each spring assembly.

4.2 Baseplate-mounting procedures

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

25

«
...
25
26
27
28
29
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Nelson Страницы: 12

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: INOXPA Страницы: 20

POWERMASTER III

Бренд: Lincoln Страницы: 6

Бренд: KNF Страницы: 22

Бренд: Rinnai Страницы: 2

Nano-Flow 2,600

Бренд: Cobalt Digital Inc Страницы: 2

Бренд: Nagman Страницы: 15

Бренд: German pool Страницы: 17

Altherma 3 R MT F+W

Бренд: Daikin Страницы: 68

Бренд: DAB Страницы: 25

Бренд: ICP Страницы: 16

Бренд: BA Pumps & Sprayers Страницы: 18

Бренд: Water Ace Страницы: 16

Бренд: Bock Water heaters Страницы: 56

Бренд: Wayne Страницы: 12

Бренд: YAMADA Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды