ITT Goulds Pumps IC Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 97

background image

•

Do not modify the equipment without approval from an authorized ITT representative.

•

Only use parts that are provided by an authorized ITT representative.

1.2.6.1 Description of ATEX

The ATEX directives are a specification enforced in Europe for electrical and non-electrical equip-
ment installed in Europe. ATEX deals with the control of potentially explosive atmospheres and the
standards of equipment and protective systems used within these atmospheres. The relevance of the
ATEX requirements is not limited to Europe. You can apply these guidelines to equipment installed in
any potentially explosive atmosphere.

1.2.6.2 Guidelines for compliance

Compliance is fulfilled only when you operate the unit within its intended use. Do not change the con-
ditions of the service without the approval of an ITT representative. When you install or maintain ex-
plosion proof products, always comply with the directive and applicable standards (for example, IEC/
EN 60079–14).

1.3 Product approval standards

Regular standards

WARNING:

Use of equipment unsuitable for the environment can pose risks of ignition and/or explo-
sion. Ensure the pump driver and all other auxiliary components meet the required area
classification at the site. If they are not compatible, do not operate the equipment and con-
tact an ITT representative before proceeding.

All standard products are approved according to CSA standards in Canada and UL standards in
USA. The drive unit degree of protection follows IP68. See the nameplate for maximum submersion,
according to standard IEC 60529.

All electrical ratings and performance of the motors comply with IEC 600341.

Explosion-proofing standards

All explosion-proof products for use in explosive atmospheres are designed in compliance with one
or more of the following approvals:

•

EN, ATEX Directive 94/9/EC

•

FM According to NEC

•

Class 1 Div 1 Groups “C”, and “D”

•

Class 2 Div 1 Groups “E”, “F”, and “G”

•

Class 3 Div 1 Hazardous Locations

ATEX/IECEx:

•

Group: IIC

•

Category:

•

Temperature Class: T4 (for ambients up to 100ºC)

•

ATEX Marking: Ex II G

2D Barcode Here

1.3 Product approval standards

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

9

«
...
9
10
11
12
13
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

BURKAY 102 Series

Бренд: A.O. Smith Страницы: 24

Бренд: YGHP Страницы: 14

Бренд: IBC Страницы: 22

Бренд: Jandy Страницы: 108

Бренд: EasyPro Страницы: 4

Бренд: Navien Страницы: 157

Бренд: Navien Страницы: 2

Бренд: Navien Страницы: 4

Бренд: Radiant Страницы: 8

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Бренд: Edwards Страницы: 16

Бренд: T.I.P. Страницы: 136

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

Бренд: Grundfos Страницы: 35

Бренд: DAYLIFF Страницы: 12

Бренд: AMICOCIRC Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды