ITT Goulds Pumps IC Скачать руководство пользователя страница 54

Страница: 54 / 97

Driver

End plate

Figure 25: Placement of driver half of coupling guard

Place the driver-side end plate in the annular groove of the driver-half of the coupling guard.

Use a bolt, a nut, and two washers to secure the coupling guard half to the end plate. Hand-
tighten only.
The hole is located on the driver-side of the coupling guard half.

Slide the driver-half of the coupling guard towards the motor so that the coupling guard com-
pletely covers the shafts and coupling.

Slide to fit

Driver

Figure 26: Slide driver-half of coupling guard towards motor

Use a nut, a bolt, and two washers to secure the coupling guard halves together.

10. Tighten all nuts on the guard assembly.

5.6 Bearing lubrication

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. En-

sure bearings are properly lubricated prior to startup.

5.6 Bearing lubrication

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды