ITT Goulds Pumps IC Скачать руководство пользователя страница 37

Страница: 37 / 97

Pour grout through the grout hole into the baseplate up to the level of the dam.
When you pour the grout, remove air bubbles from it by using one of these methods:

•

Puddle with a vibrator.

•

Pump the grout into place.

Allow the grout to set.

Item Description

Baseplate

Shims or wedges

Grout

Foundation

Sleeve

Dam

Bolt

Figure 18: Pour grout into baseplate

Fill the remainder of the baseplate with grout, and allow the grout to set for at least 48 hours.

Item Description

Baseplate

Grout

Foundation

Dam

Bolt

Figure 19: Fill remainder of baseplate with grout

Remove the leveling jackscrews after the grout hardens in order to remove any stress points.

Tighten the foundation bolts.

Make sure that treatment of the concrete is in accordance with DIN 1045.

4.5 Grout the baseplate

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды