ITT Goulds Pumps IC Скачать руководство пользователя страница 59

Страница: 59 / 97

5.8 Pump priming

5.8.1 Prime the pump with the suction supply above the pump

Slowly open the suction isolation valve.

Open the air vents on the suction and discharge piping until the pumped fluid flows out.

Close the air vents.

Item Description

Discharge isolation valve

Check valve

Suction isolation valve

Figure 29: Suction supply above pump

5.8.2 Prime the pump with the suction supply below the pump

Use a foot valve and an outside source of liquid in order to prime the pump. The liquid can come
from one of these sources:

•

A priming pump

•

A pressurized discharge line

•

Another outside supply

Close the discharge isolation valve.

Open the air vent valves in the casing.

Open the valve in the outside supply line until only liquid escapes from the vent valves.

Close the vent valves.

Close the outside supply line.

5.8 Pump priming

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды