background image

INSTALLATION AND SERVICE MANUAL 

Electric Power Water Heater

 

        12kW – 162kW 

NOTE: retain this manual for future reference 

Installation  and service must be performed  by Qualified Service Personnel Only.

 

 

WARRANTY: 

 

Factory  warranty (available on web site)  does  not apply to units improperly installed or improperly operated. 
 
Experience  has shown that improper  installation or system design, rather than faulty equipment, is the cause of 
most operating problems. 
 
Excessive  water  hardness  causing  a  lime/scale  build-up  in  the  heater  and/or  on  the  immersion  heating 
elements is not the fault of the equipment and  is  not  covered  under  the  manufacturer's  warranty.  (See  Water 
Treatment and  Water Chemistry) 

Do  not  energize  electrical  system before  heater is completely  filled with  water. Damage  caused to the 
immersion  heating  elements by dry fire is not  covered  under  the  manufacturer's  warranty.  Follow  start up 
procedure in the manual. Water  heater corrosion and  component failure caused  by  air-borne  chemical  vapors 

is  not covered under the manufacturer's  warranty. Corrosion damage caused by current leakage due to 
improper  grounding  of  electrical  systems  or electronic  components to  the  storage  tank and related  piping 
is  not  covered  by  the manufacturer's warranty. Under no circumstance  will the manufacturer  be liable for 
consequential damages resulting  from the installation or use of this equipment. Correct  installation procedures 
and local codes must be adhered to. 

 

SPECIAL INSTRUCTIONS TO OWNER: 

WARNING: 

Improper Installation, Adjustment, Alteration, Service or Maintenance can cause injury or 

property damage. Refer to this manual. For assistance or additional information consult a qualified 

installer, service agency or the electric utility

 

CHECKING EQUIPMENT: 

This  manual  supplies  information  for the installation, operation  and servicing of the appliance.  It is strongly 
recommended  that  this manual  be  reviewed completely  before proceeding  with  an installation.  Upon receiving 
equipment,  check for signs of shipping damage. Pay  particular  attention  to  parts  accompanying the water heater, 
which may show signs of being hit  or  otherwise  being  mishandled.  Verify  total  number of  pieces shown  on 
packing slip  with those actually received.  In case there is damage or a shortage, immediately notify carrier. 

DO NOT USE THIS APPLIANCE IF ANY PART  HAS  BEEN  UNDER  WATER.  THE POSSIBLE 

DAMAGE  TO  A FLOODED APPLIANCE  CAN  BE EXTENSIVE  AND PRESENT NUMEROUS 

SAFETY HAZARDS. ANY APPLIANCE  THAT HAS BEEN UNDER WATER MUST BE REPLACED. 

 

Содержание VR-1000-(kW)






















Отзывы: