background image

 

Immersion thermostat (one per 54kW of input as standard). 

 

180°F (82.2°C) temperature operation is possible to provide water for sanitizing applications. 

 

150 PSI 

 

Insulated to meet the latest edition of ASHRAE 90.1 energy efficiency standards. 

 

3 year limited warranty provides protection against failure of tanks due to defects in material and 
workmanship. 

 

Underwriter's Laboratories, Inc. listing for all models as a commercial electric water heater. 

OPTIONAL EQUIPMENT: 

The following items are available as extra cost options: 

 

Electronic low water cut-off prevents energizing of the heater when it is not filled with water. 

 

Pilot lights - Monitor on-off cycle of contactors. 

 

Manual limiting switches with indicating lights to permit heater kW input to be manually limited as 
desired. 

 

Temperature and pressure gauges are available installed flush with the jacket to monitor heater 
performance. 

 

Electronic step controller module provides electronic thermostat control. 

 

Safety door interlock prevents opening of access door while heater is energized. 

 

Shunt trip disconnect provides power disconnect upon a control sensed malfunction. 

 

Alarm bell provides an audible alarm to warn of various control failures. 

 

Time clock to control off-on cycles of the heater as programmed by the owner or electric utility 
requirements. 

 

Low water pressure switch. 

 

High water pressure switch. 

 

 

12 

 

Содержание VR-1000-(kW)






















Отзывы: