IPG IX-6168-PS Скачать руководство пользователя страница 57

Страница: 57 / 136

6-1

Pneumatic

Components

A workstation typically includes pneumatic components for distributing and

controlling vacuum, compressed air, and sometimes purge gases. Here are some

typical uses:

The pneumatic components may include electrically controlled solenoids,

mechanically operated switches and shutoffs, filters and mist separators, pressure

gauges and regulators, flow valves and meters, ballast tanks, and various tubes and

fittings.

Pneumatic Supply

Typical Uses

Vacuum

Holding the part on the chuck

Compressed Air

Opening the beam stop
Operating other pneumatically actuated devices such as mirrors or
specialized part-handling devices
Floating the part-handling stages on an air bearing
Purging contaminants from the processing site

High-Purity Purge Gas

Purging oxygen from the beam delivery system
Purging contaminants from the processing site

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

IPG IX-6168-PS, Справочник по аппаратуре, Страница: 57 / 136

Результаты поиска

Содержание IX-6168-PS

Отзывы: