IPG IX-6168-PS Скачать руководство пользователя

Страница: 110 / 136

Video Components

11-2

Digital Process-Viewing Camera

The digital process-viewing camera points down at the processing location from an

angle. The camera optics include mirrors that correct for the viewing angle, so that the

displayed video image has the right proportions.

Figure 91: Digital Process-Viewing Camera Assembly

Camera Adjustments

To adjust the camera:

✧

Turn the zoom collar to zoom in or out.

✧

Turn the focus micrometer to focus the image.

✧

Turn the Y-position adjustment screw to move the camera front-to-back.

✧

Turn the X-position micrometer knob to move the camera side-to-side.

Digital Process
Camera

Ethernet Cable

Power and
IO Cable

Note

When turning the zoom
collar, grip it between the
thumb and finger. Turning it
by pressing a single finger
against it puts stress on the
lens set screws.

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды

IPG IX-6168-PS, Справочник по аппаратуре

Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды