IPG IX-6168-PS Скачать руководство пользователя страница 119

Страница: 119 / 136

11-11

Video Illuminators

✧

To rotate the illuminator toward or away from the camera, loosen the two M4

rotation adjustment screws, make the adjustment, and retighten the screws.

Figure 101: Adjusting the Process Camera Illuminator

The LEDs in the process illuminator have a very long life but will eventually need to

be replaced.

To replace the Process Camera Video Illuminator:

Turn off the power to the illuminator.



The IX-6168-LUM is equipped with the programmable lighting controller option,

therefore this operation needs to be done in the workstation’s software. Refer to

the included IX Series Laser Workstation Setup and Operation: Chroma.NET

manual (part # MAN-1) for more instructions on programming the video camera

illuminators.

a. Click the “Main” icon in the lower left corner of the main workstation screen,

and click “Process” under the “Camera View” tab.

M5
Position
Adjustment
Bolt

M4
Rotation
Adjustment
Screw (2)

Twist-Lock

Cable

Connector

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

IPG IX-6168-PS, Справочник по аппаратуре, Страница: 119 / 136

Результаты поиска

Содержание IX-6168-PS

Отзывы: