IPG IX-6168-PS страница 37 Скачать руководство пользователя

Страница: 37 / 136

3-5

Starting the System

3. Turn on the air and vacuum supplies and any nitrogen or helium purge-gas sup-

plies your system uses.

4. Press the green

Power On

button on the front of the workstation. The computer

and internal electronic systems start up.

Figure 21: SYSTEM POWER - ON/OFF buttons

5. Log on to the workstation’s Windows computer with user name

Operator

. The

factory-set password is

6. Start the IPG Photonics software by double-clicking its icon on your desktop.
7. When the startup screen loads, click the “

” button, located in the upper

right corner.

Figure 22: Chroma.NET Startup Screen with Login Button

8. When the Login screen loads, pull-down your status/function or user name and

enter your password. The factory-configured password for the built-in user

accounts is

“1

”.

Green Power ON Button

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды

IPG IX-6168-PS, Справочник по аппаратуре

Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды