IPG IX-6168-PS страница 114 Скачать руководство пользователя

Страница: 114 / 136

Video Components

11-6

The LEDS in the illuminator have a very long life but will eventually need to be

replaced.

To replace the Inspection Camera Video Illuminator:

Turn off the power to the illuminator.



The IX-6168-LUM is equipped with the programmable lighting controller option,

therefore this operation needs to be done in the workstation’s software. Refer to

the included IX Series Laser Workstation Setup and Operation: Chroma.NET

manual (part # MAN-1) for more instructions on programming the video camera

illuminators.

a. Click the “Main” icon in the lower left corner of the main workstation screen,

and click “Inspection” under the “Camera View” tab.

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды

IPG IX-6168-PS, Справочник по аппаратуре

Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды