IPG IX-6168-PS страница 16 Скачать руководство пользователя

Страница: 16 / 136

Safety

1-10

System Signalling Light Tower with Alarm

The optional IPG Photonics System Signalling Light Tower is a feature available in the

IX-6168-PS systems. The light tower is mounted on the top of the processing enclosure

and is used to indicate the system status. The tower also includes an audio alarm that

is controlled at the base of the tower.
The following describes the standard IPG Photonics Signalling Light Tower:

Red Flashing with Alarm:

System Error

Red Solid:

System Error Acknowledged

Yellow Flashing:

System Warm up

Yellow Solid:

Maintenance/Manual Override Mode

Green Flashing:

System Processing

Green Solid:

Process Complete / System Ready

Clear Solid:

system is turned on and the IPG Photonics software is started.

Alarm:

Volume control by turning ring at base of light tower.

Содержание IX-6168-PS









































































































































Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды

IPG IX-6168-PS, Справочник по аппаратуре

Результаты поиска

Содержание IX-6168-PS

Отзывы:

Похожие инструкции для IX-6168-PS

Бренды по названию

Популярные бренды