Haemonetics PCS 2 Скачать руководство пользователя страница 118

Страница: 118 / 134

7-8

PCS2 Service Manual

Parts Description

Part No.

Returnable

Cabinet Final Assembly

36922-00

Top Deck Distribution Power Cable..................................................35227-00

Top Deck Distribution Signal Cable..................................................35228-00

Front Panel Distribution Cable..........................................................35226-00

Drain Bag .........................................................................................35643-00

IV Pole Assembly (AC) .....................................................................36895-02

Saline Pole Assembly .......................................................................47955-02

Power Cord Assembly......................................................................19417-00

Top Cover Assembly

36931-00....................X

Top Cover .........................................................................................34891-03....................X

Membrane Panel Assembly .............................................................37107-00....................X

Membrane Panel ........................................................................37108-00

Vacuum Display .........................................................................36387-00

Control Panel Distribution Card..................................................35218-00 ....................X

Display Power Cable..................................................................35233-00

Display Signal Cable..................................................................35232-00

Control Distribution Cable Upgrade Kit

49320-00

Control Panel Distribution Cable ......................................................35231-00

Top Cover Decorative Panel Assembly ............................................47242-00

Decorative Panel ........................................................................35125-02

Retainer Pad...............................................................................13549-02

Centrifuge Assembly (complete)

36917-00....................X

Centrifuge Assembly (w/o optics) ....................................................36919-00....................X

O-ring .........................................................................................37027-01

Drain Tube ..................................................................................06299-06

Fluid Sensor Assembly.....................................................................35294-00

Optics Assembly (includes both block and cable) ..........................38870-00....................X

Cover Switch Assembly....................................................................35347-00

Cap/Cover Assembly .......................................................................36920-00

Headless Shoulder Screw on Cover Hinge................................35290-00

Shoulder Screw, Socket Head ...................................................09578-02

Nylon Washer .......................................................................14269-07

Screw, Socket Head Cap .....................................................19600-02

Screw, Socket Head (Base Hinge).............................................62310-907

Cover Window ............................................................................35274-00

Screw, Button Head Socket .......................................................69110-504

Centrifuge Knob Replacement Kit .......................................38461-00

Cover Latch Knob Disk ........................................................36859-02

Содержание PCS 2







































































































































Результаты поиска

Содержание PCS 2

Отзывы:

Похожие инструкции для PCS 2

Бренды по названию

Популярные бренды

Haemonetics PCS 2, Руководство пользователя

Результаты поиска

Содержание PCS 2

Отзывы:

Похожие инструкции для PCS 2

Бренды по названию

Популярные бренды