manualshive.com logo in svg

Freescale Semiconductor KKL02Z32CAF4R, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor KKL02Z32CAF4R Скачать руководство пользователя страница 308

FTFA_FSTAT field descriptions

Field

Description

7

CCIF

Command Complete Interrupt Flag

The CCIF flag indicates that a flash command has completed. The CCIF flag is cleared by writing a 1 to
CCIF to launch a command, and CCIF stays low until command completion or command violation.

The CCIF bit is reset to 0 but is set to 1 by the memory controller at the end of the reset initialization
sequence. Depending on how quickly the read occurs after reset release, the user may or may not see the
0 hardware reset value.

0

Flash command in progress

1

Flash command has completed

6

RDCOLERR

Flash Read Collision Error Flag

The RDCOLERR error bit indicates that the MCU attempted a read from a flash memory resource that
was being manipulated by a flash command (CCIF=0). Any simultaneous access is detected as a collision
error by the block arbitration logic. The read data in this case cannot be guaranteed. The RDCOLERR bit
is cleared by writing a 1 to it. Writing a 0 to RDCOLERR has no effect.

0

No collision error detected

1

Collision error detected

5

ACCERR

Flash Access Error Flag

The ACCERR error bit indicates an illegal access has occurred to a flash memory resource caused by a
violation of the command write sequence or issuing an illegal flash command. While ACCERR is set, the
CCIF flag cannot be cleared to launch a command. The ACCERR bit is cleared by writing a 1 to it. Writing
a 0 to the ACCERR bit has no effect.

0

No access error detected

1

Access error detected

4

FPVIOL

Flash Protection Violation Flag

The FPVIOL error bit indicates an attempt was made to program or erase an address in a protected area
of program flash memory during a command write sequence . While FPVIOL is set, the CCIF flag cannot
be cleared to launch a command. The FPVIOL bit is cleared by writing a 1 to it. Writing a 0 to the FPVIOL
bit has no effect.

0

No protection violation detected

1

Protection violation detected

3–1

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

0

MGSTAT0

Memory Controller Command Completion Status Flag

The MGSTAT0 status flag is set if an error is detected during execution of a flash command or during the
flash reset sequence. As a status flag, this bit cannot (and need not) be cleared by the user like the other
error flags in this register.

The value of the MGSTAT0 bit for "command-N" is valid only at the end of the "command-N" execution
when CCIF=1 and before the next command has been launched. At some point during the execution of
"command-N+1," the previous result is discarded and any previous error is cleared.

Memory Map and Registers

KL02 Sub-Family Reference Manual, Rev. 2.1, July 2013

308

Freescale Semiconductor, Inc.

Содержание KKL02Z32CAF4R
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды