Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 156

background image

DRIVE PROGRAMMING

Setting Operating Parameters

49

8.

Deceleration Time [SET–12]:

Enter a time in seconds to slow down from maximum frequency to stop.

Recommended defaults are 2 seconds for submersibles and 30 seconds for surface/boost pumps. This
setting is only effective when

Stop Mode [SET

–

16]

is set to

Decelerate

. Additional deceleration curves can be

added for more precise control through selected frequency ranges. Refer to

“Acceleration/Deceleration

Control” on page 71

9.

Low Frequency Limit [SET–13]:

The lowest frequency (speed in Hz) allowed by the VFD in any mode.

10.

High Frequency Limit [SET–14]:

Enter the highest frequency (speed in Hz) allowed by the VFD in any

mode.

11.

PID Mode [SET–17]:

Enables or disables PID control, either direct or inverse.

12.

PID Feedback Source [SET–18]:

Selects an input terminal for PID Feedback source. Be sure to config

-

ure the terminal for the correct impedance.

13.

PID Feedback Unit [SET–19]:

Selects a measurement unit for PID feedback.

14.

Feedback Max [SET–20]:

Enter the maximum reading of the feedback source. This is used to scale the

sensor. For example: if using a 0–200 psi transducer, enter 200.

15.

PID Setpoint [SET–21]:

Enter the desired value for the drive to maintain in PID mode, running in Auto.

This parameter can also be changed through keypad control.

16.

PID Low Frequency Limit [SET–22]:

PID frequency output will be limited to this value.

17.

PID High Frequency Limit [SET–23]:

PID frequency output will be limited to this value.

18.

Language:

Select a desired language for the display. Press the

Menu

button and then press the

Back

but

-

ton. Use the

Down

keys to display

Set Language

.

19.

Clock:

Set current time and date. This setting is used to record real-time data for faults, parameter

changes, etc. Press the

Menu

button and then press the

Back

button. Use the

Down

keys to display

Set Time

.

Verify Control Terminal Settings

For each type of control hardware that has been connected to the system—sensors, switches, BAS, etc.,
make sure that the matching function parameters have been identified for the input terminals. For more
information, refer to

“Example Configurations” on page 43

or to

“Parameter Descriptions > I/O Menu” on

Enter or Verify Optional Settings

If using any of the optional features available in the system, make sure that all related parameters are set for
the desired operation. Refer to the application descriptions in

“Operation” on page 63

for information about

these features:
•

Automation features:

Refer to

“Standard Operation with an Automated Control System” on page 66

•

Protection features:

Refer to

“Protection Features” on page 75

•

Communications features:

Refer to

“Communications” on page 85

.

•

Multi-Motor applications:

Refer to

“Multi-Motor (MMC) Relay Control for Pump Applications” on

.

For more details on individual parameter settings, refer to

“Parameter Reference Tables” on page 115

.

«
...
47
48
49
50
51
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: Danfoss Страницы: 54

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 197

Бренд: Danfoss Страницы: 284

Бренд: Danfoss Страницы: 53

ECI-42 K1 Series

Бренд: ebm-papst Страницы: 28

Бренд: Bastl Instruments Страницы: 2

Бренд: Kalatec Automacao Страницы: 24

Бренд: GU Страницы: 13

Бренд: Xinje Страницы: 121

Бренд: Masterflex Страницы: 12

Бренд: CHINSC ELECTRIC Страницы: 169

Бренд: Penta KB Power Страницы: 20

CACR-HR BAB Series

Бренд: YASKAWA Страницы: 293

LDP-C 120-40 NG

Бренд: PICOLAS Страницы: 40

Бренд: Fagor Страницы: 96

Бренд: National Instruments Страницы: 33

Бренд: YASKAWA Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды