Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 128

Страница: 128 / 156

PARAMETER REFERENCE TABLES

Parameter Descriptions > ADV Menu

128

Parameter Descriptions > ADV Menu

AR = Adjustable while running.

CODE Mod

Bus AR Display Name

Range

Description

ADV-00 0768 Y Upper Bound Int 0 to 100%

Upper limit for the integral gain (I), which limits the output frequency.

Upper Limit Freq = VFD Max Freq Main [VFD-00] x Upper Bound Int [ADV-

00].

Too large integral value will cause a slow response to sudden load changes.

This could cause motor stall or machine damage.

ADV-01 0769 Y PID Out Limit

0 to 110%

Maximum PID command limit. Percentage of Maximum Output Frequency

[VFD-00].

ADV-02 0770 Y Password Input

0 to 65535

Password protect from modifying parameters.

ADV-03 0771 N Parameter Reset 0_Disabled

1_Write protect

3_Reset KWH

4_Reset all Param

5_Reset M Run T

Select stored data to be reset.

ADV-05 0773 Y Password Lock

0_Unlocked

1_Locked

When setting password protection for the first time, set password in Pass

word Input [ADV-02] and then Password Lock [ADV-05] becomes 1-

Locked. To permanently disable password protection, unlock parameters by

entering password in Password Input [ADV-02] and then set Password

Lock [ADV-05] to 0-Unlocked. If drive is unlocked by a password and pass

word lock is not set to 0-Unlocked, the next reboot of the VFD will lock the

VFD again.

ADV-06 0774 Y Acc/Dec Type

0_Linear Acc/Dec

1_Auto Acc/L-Dec

2_L-Acc/Auto Dec

3_Auto Acc/Dec

4_Lin, Auto Stall

Provides automated acceleration and deceleration with stall prevention.

0_Linear Acc/Dec: Accelerates and decelerates according to the setting of

SET-11~12 and VFD-19~24.

1_Auto Acc/L-Dec: Auto detects the load torque and accelerates for the

fastest acceleration time and smoothest start current. Deceleration is linear

according to setting of SET-11-12 and VFD-19-24.

2_L-Acc/Auto Dec: Linear acceleration according to setting SET-11~12 and

VFD-19~24. Auto detects the load re-generation and stops the motor

smoothly with the fastest decel time.

3_Auto Acc /Dec: Auto detects load for smoothest operation for accelera

tion and deceleration.

4_Lin, Auto Stall: Stall prevention by auto accel./decel being limited by

SET-11~12 and VFD-19~24.

ADV-07 0775 N Acc/Dec Format 0_Unit 0.01 Sec

1_Unit 0.1 Sec

Precision of acceleration and deceleration.

ADV-08 0776 Y Energy Saving

0_Disable

1_Enable

When the output frequency is constant, the output voltage will auto

decrease by the load reduction. The drive will operate with minimum

power.

ADV-09 0777 Y E-Saving Gain

10 to 1000%

Determines speed of adjusting output voltage in relationship to load reduc

tion. If the motor oscillates or has a quick temperature rise, the value should

be increased.

ADV-10 0778 N MMC Mode

0_Disabled (default)

1_Equal Run Time

2_Soft Start mode

3_Lead-Lag

4_Run Time Alt

5_Rotate Lead

Type of operation for Multi-Motor Control.

ADV-11 0779 N Motor Quantity

1 (default) to 7

Number of motors in MMC relay control setup. Limit is 3 without I/O card.

When I/O card is installed, selections 1-7 are available.

ADV-12 0780 N Aux Mtr Stop Hz 0 to VFD-00

When output frequency is less than value and remains for duration of ADV-

15, motors will be shut down one by one.

ADV-13 0781 N Alt Run Time

0.0 to 60000 Min

Duration of running a motor before switching to another motor.

ADV-14 0782 N S-Start ON Dly

0.0 to 3600 Sec

Delay time before switching on motor.

ADV-15 0783 N S-Start Off Dly

0.0 to 3600 Sec

Delay time before switching off motor.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды