Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 153

Страница: 153 / 156

GLOSSARY

Applicable Standards

153

GLOSSARY

Acronym/

Term

Definition

Description

AWG

American Wire Gauge

A standardized measurement of wire diameters important for

determining current-carrying capacity.

BAS

Building Automation System

A computer-based control system that controls and monitors a

building's mechanical and electrical equipment.

BMS

Building Management System

A computer-based control system that controls and monitors a

building's mechanical and electrical equipment.

BPC

Bypass Controller

EMI

Electromagnetic Interference

See RFI.

FLA

Full Load Amperes

The nameplate amperage rating of the motor when it is running

at its designed horsepower and on the motors designed voltage.

GFCI

Ground Fault Circuit Interrupter

A fast-acting circuit breaker designed to shut off electric power

in the event of a ground-fault within as little as 1/40 of a second.

GPM

Gallons per Minute

A unit of volumetric flow rate in the United States.

HMI

Human Machine Interface

An interface that permits interaction between a human and a

machine, such as a display and keyboard.

HOA

Hand/Off/Auto switching

IGBT

Insulated Gate Bipolar Transistor

A three-terminal power semiconductor device used as an elec

tronic switch to synthesize complex waveforms with pulse-

width modulation in a variable-frequency drive (VFD).

International Protection rating

Used as protection measures for motors, electrical devices and

motors.

LDT

Load Detection Trip

MCCB

Molded Case Circuit Breaker

An MCCB provides protection by combining a temperature sen

sitive device with a current sensitive electromagnetic device.

MMS

Manual Motor Starter

An electromechanical protection device used to switch motors

ON/OFF manually and to provide fuseless protection against

short-circuit, overload and phase failures.

MOL

Motor Overload

NEC

National Electrical Code

A regionally adoptable standard for the safe installation of elec

trical wiring and equipment in the United States.

NEMA

National Electrical Manufacturer Association

The largest trade association of electrical equipment manufac

turers in the United States. NEMA publishes more than 700 stan

dards for electrical enclosures, motors and magnet wire, AC

plugs and receptacles, etc.

PFC

Power Factor Correction

PID

Proportional Integral Derivative

A control loop feedback mechanism used in applications requir

ing continuously modulated control.

PLC

Programmable Logic Controller

A digital computer used for automation of typically industrial

electromechanical processes.

PMA

Pump and Motor Assembly

PWM

Pulse Width Modulation

A modulation technique used to control the power supplied to

electrical devices, especially for motor speed control.

RFI

Radio Frequency Interference

A disturbance generated by an external source that affects an

electrical circuit by electromagnetic induction, electrostatic cou

pling, or conduction.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды