Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 106

Страница: 106 / 156

MAINTENANCE

Troubleshooting

106

OL-2 (OL-2)

• Overload

•

ov at accel (ovA)

• DC BUS over-voltage during

acceleration (230V: 410VDC;
460V: 820VDC; 575V: 1116VDC;
690V: 1318VDC).

• Check if the input voltage falls within the rated VFD input voltage

range.

• Check for possible voltage transients.
• If DC BUS over-voltage is due to regenerative voltage, increase the

acceleration time or add an optional brake resistor.

ov at decel (ovd)

• DC BUS over-voltage during

deceleration (230V: 410VDC;
460V: 820VDC; 575V: 1116VDC;
690V: 1318VDC).

• Check if the input voltage falls within the rated VFD input voltage

range.

• Check for possible voltage transients.
• If DC BUS over-voltage is due to regenerative voltage, please

increase the Deceleration Time or add an optional brake resistor.

ov at normal SPD (ovn)

• DC BUS over-voltage at constant

speed (230V: 410VDC; 460V:
820VDC; 575V: 1116VDC; 690V:
1318VDC).

• Check if the input voltage falls within the rated VFD input voltage

range.

• Check for possible voltage transients.
• If DC BUS over-voltage is due to regenerative voltage, please

increase the Deceleration Time or add an optional brake resistor.

ov at stop (ovS)

• Over-voltage at stop

• Check if the input voltage falls within the rated VFD input voltage

range.

• Check for possible voltage transients.

ov HW error (Hd2)

• Hardware failure in voltage

detection

• Reboots the power. If fault code is still displayed on the keypad,

please call technical support.

Over slip error (oSL)

• Slip exceeds Motor-19 setting and

time exceeds Motor-20 setting.

• Check if motor parameter is correct (please decrease the load if

overload

• Check the settings of Motor-19 and Motor-20.

Over-torque 1 (ot1)

• Current exceeds detection

criteria.

• Check whether the motor is overloaded.
• Check whether motor rated current setting (SET-03) is suitable.

Over-torque 2 (ot2)

• Current exceeds detection

criteria.

• Check whether the motor is overloaded.
• Check whether motor rated current setting (SET-03) is suitable.

Overpressure (OPRS)

• Overpressure

•

Password error (Pcod)

• Password is locked.

• Power off and restart the driver before entering the correct password

PC err address (CE2)

• Illegal data address

• Check if the communication address is correct

PC err command (CE1)

• Communication command is

illegal

•

PC err data (CE3)

• Illegal data value

•

PC slave fault (CE4)

• Data is written to read-only

address

• Check if the communication address is correct

PC time-out (CE10)

• Modbus transmission time-out

•

Phase lacked (OrP)

• Phase Loss protection

• Check that all 3 input phases are connected without loose contacts.
• For models 40hp and above, please check if the AC input circuit fuse.

PID Fbk error (AFE)

• PID loss (ACI)

• Check the wiring of the PID feedback
• Check the PID parameters settings

Rotor Pos Error (RoPd)

• Initial rotor position detection

error

•

S1-emergy stop (S1)

• Emergency stop for external

safety

•

Short-circuit (occ)

• Short-circuit is detected between

upper bridge and lower bridge of
the IGBT module

• Please call technical support.

Shutdown (SHDN)

•

STO (STO)

• Safe Torque Off function active

•

Fault

Description

Corrective Action

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды